Tube Removal
Make an already difficult job easier with the help of tube removal tools. They are designed for use in boiler and heat exchanger applications, allowing you to remove tubes quickly and easily.
-
Tube Size: 0.375" to 3.000" (9.5 - 76.2mm) OD
-
Tube Size: 0.375" to 3.000" (9.5 - 76.2mm) OD
-
Tube Size: 0.500" to 2.500" (12.7 - 63.5mm) OD
-
Tube Size: 0.500" to 2.000" (12.7 - 50.8mm) OD
Elliott’s hydraulic pumps are used to power the Collet Style Tube Tugger, Cyclegrip Semi-Continuous Puller, Tube Tuggers, and Stub Tugger. The hydraulic pumps’ compact design is ideal for use in confined work areas.
-
Maximum Pressure: 5,000 or 10,000 PSI
-
Power Source: Electric 110V or 220V, Pneumatic, or Manual
Stub Tugger
Hydraulic Tube Pulling System
Elliott’s Stub Tugger is a powerful hydraulic tube pulling system for removing tubes from both heat exchangers and boilers.
-
Tube Size: 0.375” to 3.000” (9.5 – 76.2mm) OD
-
Type: Stub Puller
-
Application: Heat exchangers and boilers
-
Pulling Capacity: 30 Ton (27.2Mt)
-
Stroke: 6" (152.4mm)
SpeedCut
Tube Bundle Cutter
Equipped with a rugged Baldor© Motor and the highly productive Automatic Cutting Force Control, Elliott’s SpeedCut is a quick and cost-effective way to cut through tube bundles and shells in a single pass.
-
Type: Tube Bundle Cutter
-
Tube Bundle Sizes: Up To 98.5" (2.5m) diameter.
-
Automatic Cutting Force Control
-
Unattended Operation
-
Safe and Easy To Use
-
Typical Cutting Time: 20-16 minutes
Elliott's Pneumatic Hammer is the recommended tool for removing tube stubs in heat exchangers or beading tubes in firetube boilers.
-
Tube Size: 0.250" to 3.000" (6.4 - 50.8mm) OD
Elliott’s Lubricants are engineered to provide the best lubrication in tube rolling and roll beading applications. They will provide time and tool savings compared to commonly available lubricants.
-
Paste Lubricant
-
Liquid Lubricant
-
Bead Coolant
-
Cutting Oil
Cyclgrip
Semi-Continuous Tube Puller
Elliott’s Cyclgrip Semi-Continuous Tube Puller is an engineered product that continuously pulls chiller, heat exchanger, and condenser tubes after the tubes have been pulled free from the tube sheet, making it the ideal companion for the Collet Style Tube Tugger.
-
Tube Size: 0.500” to 1.000” (12.7 – 25.4mm) OD
-
Type: Tube Puller
-
Pulling Speed Per Minute: 10' (3.3m)
Elliott’s Manual Tube Puller is ideal for pulling a limited number of tubes in heat exchangers, chillers, fin fan coolers, and surface condensers.
-
Tube Size: 3/8” to 1.000” (9.5 – 25.4mm) OD
-
Type: Tube Puller
-
Application: Heat exchangers, chillers, fin fan coolers, and surface condensers
Elliott’s Jumbo Tube Buster is the recommended driving tool for Elliott’s Jumbo Knockout Tools to remove tube stubs in heat exchangers, Firetube boilers, and Watertube boilers.
-
Tube Size: 0.625” to 2.000” (15.9 – 50.8mm) OD
-
Type: Tube Buster
Suggested Articles
Do I Need Torque Control?
With the amount of rolling motors on the market, there are a lot of variables to consider. However, one of the most common questions is around torque control, setting torque, and when it’s not needed for a job.
How To Retube A Locomotive Boiler
Historically, many railroad companies used steam locomotives for transportation. Today, most steam locomotives are reserved for private rails, museums, and other charity organizations. As these systems age, they present several unique maintenance challenges that can arise due to the design and location of these units. Understanding the composition of locomotive boilers, as well as the maintenance needs, can make restoration jobs a little bit easier.
When To Retube or Replace
To get the best performance out of a vessel it’s important that it maintains necessary operating capacity. While there are several preventative maintenance procedures that can prolong the life of the vessel, eventually a decision on retubing or replacing the unit will need to be made.
Choosing The Right Tube Puller
When it comes to removing tubes, there are many different options to choose from. Hydraulic or automated pulling options can be a great way to speed up the job, reduce tube sheet damage, and improve operator ergonomics. However, before selecting a pulling package, it’s important to consider the vessel type, tube condition, and space constraints
Increase Tool Life On Tough Materials: Benefit Of Tapping Spears
In recent years, the use of exotic materials in heat exchanger tubing has become a lot more common. While these materials are great for working in tough conditions, they can have be very challenging to work with as they often require more tooling and job time. This is especially true in tube removal where pulling spears are used. Tapping spears have become an effective way to overcome many of these issues.
Boiler Tube Removal: How To Create A King Hole
With a variety of boiler tube removal methods out there, it can be difficult to determine the best approach for your application. Depending on the amount of expansion, age of the tube, and other wear factors, tubes can be extremely difficult to get out. Removing tubes through a king hole can be an easier method of removal, especially for operators with varying experience levels.