Elliott’s Rapid Hawk Assisted Tube Rolling System utilizes an electronic torque control system to precisely measure tube expansion and consistently hit target every time. For the first time, an electronic torque control can be used regardless of the motor’s power source.

• Tube Size: 0.500" to 3.00" (12.7 - 76.2mm) OD

• Torque Control

• Consistent Tube Expansion

• Operator Friendly

• Large Radial Reach

Elliott’s Tube Hole Gauges make it easy to accurately measure tube IDs and tube sheet holes found in vessels such as heat exchangers, chillers, and surface condensers.

• Tube Size: 0.375” to 2.000” (9.5 – 51.0mm) OD

Elliott’s GT Series Grooving Tools, also known as Serrating Tools, can be used manually to clean up existing grooves or can be used in milling or drilling equipment for OEM tube sheet thicknesses of 3/8” (9.5mm) through 2-1/8” (54.0mm).

• Tube Size: 0.375" to 3.000" (9.5 - 76.2mm) OD

Engineered to productively and precisely expand small tubes commonly found in oil coolers and other small heat exchangers. Elliott’s tabletop assisted tube rolling system completes the job right the first time.

• Tube Size: 0.25" to 0.625" (6.35 - 15.875mm) OD

• Direct Torque™ Electric Torque Control

• Increased Productivity

• Operator Friendly

• Consistent Tube Expansion

Elliott’s ETF Series Tube End Facers are ideal for trimming heat exchanger, condenser, and chiller tubes to a specific tube projection after tube expansion.

• Tube Size: 0.375" to 1.500" (9.5 - 38.1mm) OD

Elliott’s Tube Pilots, also known as Tube Guides, are used to pilot replacement tubes through tube sheets and tube support plates that are commonly found in heat exchangers and surface condensers.

• Tube Size: 0.500” to 1.500” (12.7 – 38.1mm) OD

Elliott’s ELC110220 is the first torque control with an Embedded Logic Controller that senses and is compatible with both 110V or 220V automatic, and manual reverse rolling motors.

• Tube Size: 0.250" to 3.000" (6.4 - 76.2mm) OD

• Voltage: 110V to 240V

• Languages: English or Spanish

• Compatibility: Elliott’s 99 Series Electric Rolling Motors (other electric motors with optional adapters)

• Auto-Reverse

Elliott’s Tube Sheet Hole Brushes clean and remove hard deposits from tube sheets and support plate holes in surface condensers and heat exchangers.

• Tube Size: 0.250” to 1.250” (6.4 – 31.8mm) OD

Elliott’s 24 Series Condenser Expanders are ideal for expanding tubes in chillers, heat exchangers, feedwater heaters, fin fan coolers, and surface condensers.

• Tube Size: 0.500" to 2.000" (12.7 - 50.8mm) OD

• Roll Type: Straight

• Application: Chiller, heat exchanger, feedwater heater, fin fan cooler, and surface condenser.

Elliott's PX24 Series offer true parallel pin tube expansion, which can reduce the stress created on welded tube joints when compared to tapered rolling.

• Tube Size: 0.750″ to 1.000″ (19.05 – 25.4mm) OD

• Roll Type: Parallel Pin Condenser Expander

• Application: Chillers, heat exchangers, feedwater heaters, fin fan coolers, and surface condensers.

Elliott’s 900 Series Flaring Boiler Expanders are self-feeding, specifically made for use in superheaters in watertube boilers or evaporator tubes. In only one operation, these expanders roll tubes parallel and flare projecting tube ends at 15 degrees from the tool center line.

• Tube Size: 0.620” to 1.500” (15.4 – 38.1mm) OD

• Roll Type: Flaring

• Application: Superheaters, watertube boilers, and evaporator tubes.

Elliott's ET850 Motor is the next evolution of push-pull motors. Offering the same USA quality and performance you're used to, with additional features to improve the operator's experience.

• Tube Size: 0.750” to 1.250” (19.1 – 31.8mm) OD

• Type: Rolling Motor

• Power: Pneumatic

• Torque: Torque Controlled

• Tube Size: 0.250" to 0.375" (6.4 - 9.5mm) OD

• Roll Type: Straight

• Application: Chiller, heat exchanger, feedwater heater, fin fan cooler, and surface condenser.

Elliott’s Lubricants are engineered to provide the best lubrication in tube rolling and roll beading applications. They will provide time and tool savings compared to commonly available lubricants.

• Paste Lubricant

• Liquid Lubricant

• Bead Coolant

• Cutting Oil

Elliott's Pneumatic Hammer is the recommended tool for removing tube stubs in heat exchangers or beading tubes in firetube boilers.

• Tube Size: 0.250" to 3.000" (6.4 - 50.8mm) OD

The Midi/Maxi Series Pneumatic Rolling Motors are manufactured with quality materials to provide motor robustness and durability for years to come.

• Tube Size: 0.750” to 2.000” (19.1 – 50.8mm) OD

• Type: Rolling Motor

• Power: Pneumatic

• Torque: Torque Controlled

Elliott’s 99 Series electric rolling motors offer better consistency, faster RPMs, and comparable torque to that of pneumatic offerings.

• Tube Size: 0.250” to 3.000” (6.4 – 76.2mm) OD

• Type: Rolling Motor

• Power: Electric 110V or 220V

• Torque: Torque Controlled with ELC

The first rolling system of its kind, offering the speed and productivity of a patent pending electric servo motor with the capability to perform parallel pin and traditional expansion.

• Tube Size: 0.625″ to 1.500″ (15.9 – 38.1mm) OD

• Parallel and Traditional Pin Tube Rolling

• Up To 2X The Speed Of Conventional Rolling

• Automatic Tool Lubrication

• Large Radial Reach

• Easy To Move

• Operator Friendly Controls